RATTMMOTOR CNC Controller Kit, 4 Axis CNC Kit with Nema23 Stepper Motor 57*76mm 270Oz-in 3A 1.8Nm, TB6600 Driver 4A, USB Mach3 CNC Motion Control Card Breakout Board, 24V Power Supply for CNC Machine

Price: $152.00
(as of Oct 06, 2025 01:24:44 UTC – Details)

Product description

Nema23 Stepper Motor 270Oz-in

Motor Type: Hybrid StepperPhase: 2 phaseStep Angle: 1.8 degree±5%Voltage: 4.8VHolding Torque: 180N.cm(270oz-in)Detent Torque: 6N.cm MaxRotor inertia: 440g.cm²Phase Resistance: 1ohmsInsultaion Class: BInductance: 3.5mH+/-20%(1KHz)

TB6600 Stepper Motor Driver Features

Original brand new stepper motor driver chip8-speed current control7 kinds of subdivision adjustableInterface uses high-speed optical couplingAutomatic half flow reduces calorific valueLarge area heat sink is not afraid of constant high temperature environmentStrong anti-high frequency interferenceInput voltage anti-reverse protectionOverheat and overcurrent short circuit protectionThrough the 3-digit dialing code, you can choose 7-step subdivision control (1, 2 / A, 2 / B, 4, 8, 16, 32), 8-step current control (0.5A, 1.0 A, 1.5A, 2.0A, 2.5A, 3.0A).

Mach3 USB Motion Control Board 4-axis

Maximum step-pulse frequency is 100KHz,which is suitable for the servo or stepping motor.Need use external 24V DC power supply to isolate USB and external port, and to make the system more stable.4 general-purpose inputs, you can connect the limit switch, estop switch, probe switch, back to zero and other device.4 general-purpose isolated relay drive output interface, can drive four relays for controlling the spindle starts, forward rotating and reverse rotating, pumps and other device.

350W 24V DC Switching Power Supply

DC output: 24V 0-14.5AInlet stability: ±0.5%Load stability: ±0.5%DC voltage of Adjustable range: ±10%AC input voltage range: 115VAC/6.5A/50HZ—-230VAC/3.4A/60HZ; Selected by switchOverload protection: 105%-135% cut off the output, automatic recoveryOver-voltage Protection: 115%-150% shut down O/P voltage, re-power on to recoverSetup/rise/hold-up time: 200ms、50ms、20ms/230VAC at full loadWithstand voltage: I/P-O/P: 1.5KvAC; I/P-FG: 1.5KvAC; O/P-FG: 1.5KvAC; 1minuteIsolation resistance: I/P-O/P、 I/P-FG、O/P-FG: 500VDC/100MΩ

How to connect the Tb6600 driver ( or Stepper Motor) to CNC Motion Control Card?

It should be noted that the wiring diagram of the 4-axis motion control card above is for reference only, then if you connect this control card and the TB6600 driver, such as connect to X-axis motor driver, then:

Driver’s “Pul+” connects to control card’s XP+ pin ,Driver’s “DIR+” connects to control card’s XD+ pin ,Driver’s ” PUL- ” pin and ” DIR- ” connection to USB Mach3 control card’s ” GND ”

Stepper motor’s wrings ( 4 wires) :

Connect stepper motor’s RED wire to driver’s A+ portConnect stepper motor’s GREEN wire to driver’s A- portConnect stepper motor’s YELLOW wire to driver’s B+ portConnect stepper motor’s BLUE wire to driver’s B- port

Package Include:

4 × Nema23 Stepper Motor 57mm4 × TB6600 Stepper Motor Driver1 × Mach3 USB CNC Control Card+USB Cable1 × DC Switching Power Supply

TB6600 Stepper Motor Driver

Description of TB6600 Stepper Motor Driver Two-phase

Electrical parameters:

Input voltage: DC9-42VInput current: 5A switching power is recommendedOutput current: 0.5-4.0AMaximum power consumption: 160WBreakdown: 1、 2 / A、 2 / B、4、 8、 16、 32Temperature Working temperature: -10-45°C; Storage temperature -40 °C-70°C

Input and output description:

PUL + : Pulse signal input + / PUL- : Pulse signal input -DIR + : Motor rotation direction control + / DIR- : Motor rotation direction control-EN + :Motor enable control + / EN- : Motor enable control-A + : Connect motor A + phase / A- : Connect the motor A- phaseB + : Connect the motor B + phase / B- : Connect the motor B-phaseVCC : Power supply positive terminal “+” / GND : Negative terminal “-“Note : DC9-42V: Do not exceed this range, otherwise it will not work properly or even damage the drive.

4 Axis CNC USB Mach3 Controller Breakout Board

1 status LED, indicate connection status on the board.Have 0-10V output port, you can use mach3 software to control the spindle motor speed.Support for 4-axis linkage, you can connect four stepper motor drives or servo drives.

Support automatic probe toolSupport Emergency inputSupport for limit switch (It is recommended that the limit switch and emergency stop switch must be installed first and can be used normally.)Support for connecting electronic handwheel

This USB motion card does not need install any USB driver, Windows2000/XP/Windows7,can directly identify (Notice: Doesn’t support Win8/win10/macOS system !!!) .If you are not familiar with the product and software features, make sure the machine’s power switch on hand, you can quickly turn off the power.Recommends that users install the emergency stop button and make sure the button is functioning properly.

The inverter interface (AVI +, AVI-) is isolated from the computer and the main control circuit, and has strong anti-interference ability.No interference signal will be introduced due to the introduction of external strong electrical equipment.This interface can output 0 ~ 10V analog signals, and can also be configured as 0 ~ 5V output.It is recommended that the limit switch and emergency stop switch must be installed first.If these protection switches are not installed, in an emergency, in addition to pressing the emergency stop to return (sometimes too late to press), and turning off the motor power (sometimes too late to turn off), the most convenient way to stop is to pull the USB cable !! As long as the USB cable is pulled, the machine will automatically stop! !! !!

350W 24V DC Switching Power Supply

Multiple protection, Stable Performance

Short circuit protection: when the output terminal is short-circuited, the power supply turns off the output, and the output voltage is 0V.Overcurrent protection: When the output current>115-150%, the output voltage turns off the output.Overload Protection: Power protection when load power＞105-135% of rated power.Temperature protection; the power supply is automatically protected at high temperatures.

Double Ball Cooling Fan and Full Metal Housing Design

With high speed and quite characteristics, it can ensure the temperature operation of the equipment and extend the service.The shell is made of aluminum alloy with high thermal conductivity system, which is reinforced and durable, and the design is more user-friendly.

Input Voltage Switch

The power supply has an input voltage 110V-220V switch button, which can adapt to different voltage requirement.Quadruple protection setting, high resistant to electricity, effectively reducing the impact of AC input.

【Motor and TB6600 Driver wiring】Stepper motor’s RED wire connects to driver’s A+ port. Stepper motor’s GREEN wire connects to driver’s A- port. Stepper motor’s YELLOW wire connects to driver’s B+ port. Stepper motor’s BLUE wire connects to driver’s B- port.
【Control Card and TB6600 Driver wiring (X-axis as an example) 】Driver’s “Pul+” connects to control card’s XP+ pin , Driver’s “DIR+” connects to control card’s XD+ pin , Driver’s ” PUL- ” pin and ” DIR- ” connection to USB Mach3 control card’s ” GND “.
【Low Noise/High Torque Hybrid Stepper Motor】23HS8430 2-phase stepper motor with a shaft diameter of 8mm, a current of 3A and an angle of 1.8°, is made of durable metal on the outside, and the perfect combination of rubber and rotor fills up the inner space and stabilizes the overall structure of the motor. The coils are made of pure copper enameled wire and the torque is up to 270oz-in (180N.cm/18kg-cm). The motor runs quietly and doesn’t cause the generator to become too hot over a long time.
【Support Forward and Reverse Control Stepper Motor Driver】42/57 TB6600 stepper motor driver with input voltage anti-reverse connection and overheat/overcurrent short circuit protection, equipped with red warning light. through the 3-digit DIP switch, you can choose 7 subdivisions (1, 2 / A, 2 / B, 4, 8, 16, 32) and 8 subdivisions (0.5A, 1.0A 1.5A, 2.0A, 2.5A, 3.0A, 3.5A) current control.
【USB Interface, Drive-free Design 4-Axis Linkage Control Card】Output pulse frequency of 400KHz, using the minimum error interpolation algorithm, high processing accuracy. Supports up to 4 axes of linkage control, of which the 4th axis can be set as the slave axis. The control card can be connected to PC-compatible computers such as laptops, desktops, tablets and other computers with a USB interface. As long as Mach3 is running, the control card can be used without installing any drivers.
【Multi-function control card】With support for automatic home return, automatic tool setting, emergency stop input, limit switch access, spindle control (PWM mode and Him electrical mode), handwheel interface and other functions. Provide up to 12-way digital signal input, 4-way with optocoupler digital signal input and isolated relay output. Strong anti-interference and high reliability.
【Stable output 24V DC power supply】Over-current, over-voltage and overload protection, power supply stable power supply, electrical energy conversion rate of up to 90%, higher efficiency. Together with the heat dissipation fan design, shell hollow design, heat dissipation ability faster and stronger, more durable performance.